Got a 06 R1. I was riding my bike as I ran over a hole in the road. It hit pretty hard suddenly the bike instantly started misfiring and died. I'm stranded on side of the road. Does anyone have any suggest5ions. Its
grees and I'm freezing. Help!!!!!
First check the switch on your side stand. A wire might have come off.
I'd be checking all the connectors you can, and the fuses.
Maybe a wire popped off you coils.
Check your leads to the spark plugs.
Make sure everything is tight on the battery terminals.
Hopefully someone else will chime in with more tips.
Good luck mate. :thumbup
Because of the sudden jolt it may have thought you was involved in an accident and activated the sensor to shut the engine down. Not sure how to reset it though.
I had the same problem once, after the bike went for a nap on its side.
If this is the same as my scenario, then it may well be the tilt sensor. Go into DIAG mode and toggle the engine on/off switch. Then switch off the ignition and retry to start the bike up.
Got a 06 R1. I was riding my bike as I ran over a hole in the road. It hit pretty hard suddenly the bike instantly started misfiring and died. I'm stranded on side of the road. Does anyone have any suggest5ions.
If you hit the kill switch while the bike is still rolling, it'll try to start and sound like misfiring. I don't know if the 2nd post was at a standstill. :dunno:
Ok guys lets try this again. it was very foggy, it was a man hole cover that dropped about 2 inches lowerthan the pavement. i ran over it at about 40 but the bikes suspension really bottomed out really hard. instantly the bike was like running on 2 cylinders misfiring and backfiring for about 2 blocks the second i pulled over and pulled the clutch it died and didnt start again. needless to say AAA sucked ass they took 5.5 hours to pickme up and flatbed the bike home. how do i reset the tilt sensor? idk whatelse to check. i know now how to go in DIAG mode. then what? what am i looking for? alll the codes have numbers but 2 of them. #20, and#21, the both say ON. WHAT DOES THAT MEAN? What ami missing????:shake:boom
To start with you can disconnect the battery for a hard reset. Give it 10min and try starting it. Find what the codes mean and go to those sensors and check their connections. During the impact a sensor might have disconnected or got broken.
WHERE CAN I DOWNLOAD THE 06 R1 WORKSHOP MANUAL. I did hard reset.Have gone through every plug wire and connection. Repaired the tilt sensor, turned over the engine and it still wont start. I ve ran system diagnostic and i get no codes. WTF am I missing??????? I spent an hour and a half on phone with mechanic from local dealership and we still couldn't figure out.....the bike when i turn the key on, it primes and i hearthe fuel pump. I pulled the spark plug cranked it over and have no spark!!!!
I downloaded the service and racing manual. i repaired the tilt sensor, went through the checklist, have no codes showing but still will not start. It will turn over just fine but it wont start. I am now checking why I have no spark. Will let you guys know asap.
Thanks
Does the bike have an immobilizer (chip inside the key). One reason for the bike turning over but not starting could be from the computer not recognizing the key in the ignition. If the computer and the key don't have the right 'code', the bike won't start. I'm really curious what the problem ends up being.
Yeah, I kinda figured. Wasn't sure if all bikes in the states were that way.
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
Yamaha R1 Forum: YZF-R1 Forums
6M posts
157.9K members
Since 2001
R1-Forum is a Yamaha R1 motorcycle enthusiasts community dedicated to Yamaha YZF 1000 R1 sportbike. Discuss performance, customization, specs, reviews and more!