Yamaha R1 Forum: YZF-R1 Forums banner

SuperStreet Bike Magazine Nov 2012 Feature: "50th Red & White Anniversary Scheme"

17K views 139 replies 50 participants last post by  1OGR1 
#1 · (Edited)
SuperStreet Bike Magazine Nov 2012 Feature: "50th Red & White Anniversary Scheme"

I was featured in the November 2012 issue of SuperStreet Bike Magazine. I attached my article of my 2004 Yamaha R1 LE at the bottom. Please let me know what you guys think:moto: Here's a link to my SSB Mag article: http://www.superstreetbike.com/features/1211_sbkp_2004_yamaha_r1/

-Engine-
*2006 Yamaha R1 LE Graves Motorsports Supersport Race Spec Engine (185 hp & 87 lbs Torque to the Rear Wheel)
*Akrapovic Evo2 Full Titanium Exhaust System
*BMC Race Air Filter
*BMW OEM Antifreeze Engine Coolant
*DID GOLD ERV3 520 Chain
*Driven Front 16 Tooth Sprocket
*Drive Systems Superlite 47 Tooth Rear Sprocket
*Factory Pro Velocity Stacks
*Graves EXUP Valve Eliminator Adaptor
*Graves Oil Pump
*Graves Smog Block Off Plates
*Graves Valve Grinding & Resurfacing of Heads
*Graves Water Pump
*H20 Performance Oversized Race Radiator
*Motul 300V Competition Synthetic Oil
*Samco Silicone Hose Radiator Kit
*STM Slipper Clutch
*YEC Base Gaskets
*YEC Head Gaskets
*YEC Valve Springs

-Electronics-
*AIM Sports GPS Module
*AIM Sports Pista Digital Dash with Full Data Acquisition
*AvioRace 2 Button Billet Stop/Start Switch
*Dynojet Ignition Module
*Dynojet Power Commander
*Shorai 1.5 lbs Lithium Battery
*Speedohealer v4
*XT Racing Potentiometer Sensor with SLS130 Quick Release Kit & Custom 54mm Fork Bracket
*YEC ECU

-Suspension-
*2006 Yamaha R1 Swingarm Powder Coated Matte Black
*17’ OZ Racing Cattiva Forged Magnesium Matte Black Front Wheel with Dunlop Superbike Slick N-Tec UK 120/70
*17’ OZ Racing Cattiva Forged Magnesium Matte Black Rear Wheel with Dunlop Superbike Slick N-Tec USA 190/55
*Ohlins FGRT 810 Forks with SBK Internals
*Ohlins YA-343 Rear Shock With Graves Spec Valving
*Ohlins SD-027 Steering Damper with Harris Performance Fork Damper Bracket

-Brakes-
*ATE Super Blue Racing Brake Fluid DOT 4
*BrakeTech Front 320mm x 6.5mm Axis/Iron SBK-Spec Full-Floating Narrow Band Rotors
*BrakeTech Rear AXIS 220mm x 5mm Full Floating Rotor
*Brembo Front Brake Reservoir Relocator Kit
*Brembo Front Clear Brake Reservoir Tubing
*Brembo CNC 108mm GP4-RR 32/36 Monoblock Front Calipers with Nickel Cadmium Finish
*Brembo HP Rear Caliper
*Ferodo SinterGrip XRAC Racing Brake Pads (with Array Cooling)
*Brembo (Model: x98.A7.C1) GP Billet LTD Race Radial Pump 19x18 Rossi/Hayden Front Brake Master Cylinder
*Galfer Rear Custom Superbike Brake Line
*HRC Rear Brake Reservoir Kit
*Spiegler Custom 3 Line Type 950 Fitting Brake Lines
*Spiegler Dry Brake Sockets with Banjo Fittings
*Spiegler Quick Disconnect Dry Brake Plugs

-Controls-
*Attack Performance Upper & Lower Triple Tree Clamps with Custom Ignition Bracket
*Brembo Clutch Half Lever
*Brembo HPK Clutch Cable Perch
*Brembo GP Master Cylinder Half Lever
*Brembo GP Remote Adjuster with Graves Motorsports Bracket
*Renthal Adjustable Clipons
*Sato Racing Adjustable Rearsets with GP Shift

-Body & Paint-
*3M Paint Protective Film by Elite Auto Films
*Catalyst Composites Race Bodywork
*CleverWolf Racing Carbon Rear Hugger
*Custom Painted “50th Anniversary of Grand Prix Racing in Red & White” by MotoGloss
*Decals by Ace Custom Graphics & Fatlace
*Graves Gloss Black Fairing Stay
*GTYR Carbon Exhaust Heat Shield
*Puig Clear Double Bubble Windscreen

-Accessories-
*Accosato Quick Release Gas Cap
*Driven Preload Gold Fork Adjustors
*Driven Hand Grips
*Gilles Chain Adjusters
*Gilles GP Lifts
*Graves Left Engine Crankcase Cover
*Graves Quick Release Fairing Stay Race Fit
*Graves Rear Brake Return Spring
*H20 Performance Custom Oversized Radiator Guard
*HRC Overflow Radiator Bottle with Brembo Clear Reservoir Tubing
*Intuitive Frame Sliders
*Moose .028 Safety Wires
*MotionPro 1/4 Quick Throttle
*ProBolt Titanium Sump Oil Drain Plug Bolt
*ProBolt Titanium Rear Axle Nut
*ProBolt Titanium Swingarm Adjusters
*ProBolt Titanium Unsprung Race Bolt Kit with Predrilled Heads
*Racebolts Titanium Front & Rear Axles
*Racebolts ¼ Turn D-Ring Fasteners
*R&G Clutch and Shifter Sliders
*R&G Swingarm Sliders
*RhinoMoto Fork Sliders
*RhinoMoto Rear Axle Sliders
*Rizoma Oil Cap
*Rizoma Pro Guard System Hand/Lever Protectors
*StompGrip Clear Four Piece Tank Kit
*StompGrip Clear Tank Protector
*StompGrip Clear UniTankTop
*Woodcraft Left & Right Engine Case Covers
*Valter Moto AR50 Aluminum Pro Racing Rear Prong Paddock Stand
*Yoyodyne Rear Titanium Race Caliper Bolts with Predrilled Heads
 

Attachments

See less See more
7
#91 · (Edited)
Thanks for the kind words:epimp Yea, I still ride it on the track cuz I have to test all my high end components I put on. But let me tell you, it definitely rides different than a stock R1:sneaky Its definitely a BEAST on the track...
 
#50 ·
WOW, sick build brother !
 
#105 ·
Thanks soooo much for the kind words Knackers:D It's definitely an honor to be chosen to be featured on SSB mag for this months issue. Yes, not only am I happy to be on SSB mag but I also won 1st place at the IMS San Mateo show last weekend:) I'm headed next to the IMS Long Beach in 2 weeks. That's the 2nd largest show in the US. I'm definitely gonna be competing against the big dogs in the motorcycle industry. We'll see how I do out there guys:corn
 
#60 ·
No SakiBomb, I'm actually not. I live in Nor Cal now. I lived in So. Cal for 11 years and moved back up here in 2009. The tracks that are close to me now are Thunderhill Raceway, Infineon Raceway, and Laguna Seca:scoots::riding I'll be entering the Custom Bike Buildoff at the International Motorcycle Show in San Mateo and Long Beach this month and next month:cool:
 
#107 ·
I actually did really well and placed 1st at the IMS Show in San Mateo:D I'm headed to IMS Long Beach in 2 weeks to compete with the big dogs. Its actually the 2nd largest IMS show in the US:fork Wish me luck:hellobye
 
#70 ·
aye. no worries..
 
#81 ·
:thumbup

This is a really good picture. Agreed with getting one of them done in HD and then framed.

 
#82 ·
I dont no what to say!!

I was featured in the November 2012 issue of SuperStreet Bike Magazine. I attached my article of my 2004 Yamaha R1 LE at the bottom. Please let me know what you guys think:moto: Here's a link to my SSB Mag article: http://www.superstreetbike.com/features/1211_sbkp_2004_yamaha_r1/

-Engine-
*2006 Yamaha R1 LE Graves Motorsports Supersport Race Spec Engine (185 hp & 87 lbs Torque to the Rear Wheel)
*Akrapovic Evo2 Full Titanium Exhaust System
*BMC Race Air Filter
*BMW OEM Antifreeze Engine Coolant
*DID GOLD ERV3 520 Chain
*Driven Front 16 Tooth Sprocket
*Drive Systems Superlite 47 Tooth Rear Sprocket
*Factory Pro Velocity Stacks
*Graves EXUP Valve Eliminator Adaptor
*Graves Oil Pump
*Graves Smog Block Off Plates
*Graves Valve Grinding & Resurfacing of Heads
*Graves Water Pump
*H20 Performance Oversized Race Radiator
*Motul 300V Competition Synthetic Oil
*Samco Silicone Hose Radiator Kit
*STM Slipper Clutch
*YEC Base Gaskets
*YEC Head Gaskets
*YEC Valve Springs

-Electronics-
*AIM Sports GPS Module
*AIM Sports Pista Digital Dash with Full Data Acquisition
*AvioRace 2 Button Billet Stop/Start Switch
*Dynojet Ignition Module
*Dynojet Power Commander
*Shorai 1.5 lbs Lithium Battery
*Speedohealer v4
*XT Racing Potentiometer Sensor with SLS130 Quick Release Kit & Custom 54mm Fork Bracket
*YEC ECU

-Suspension-
*2006 Yamaha R1 Swingarm Powder Coated Matte Black
*17’ OZ Racing Cattiva Forged Magnesium Matte Black Front Wheel with Dunlop Superbike Slick N-Tec UK 120/70
*17’ OZ Racing Cattiva Forged Magnesium Matte Black Rear Wheel with Dunlop Superbike Slick N-Tec USA 190/55
*Ohlins FGRT 810 Forks with SBK Internals
*Ohlins YA-343 Rear Shock With Graves Spec Valving
*Ohlins SD-027 Steering Damper with Harris Performance Fork Damper Bracket

-Brakes-
*ATE Super Blue Racing Brake Fluid DOT 4
*BrakeTech Front 320mm x 6.5mm Axis/Iron SBK-Spec Full-Floating Narrow Band Rotors
*BrakeTech Rear AXIS 220mm x 5mm Full Floating Rotor
*Brembo Front Brake Reservoir Relocator Kit
*Brembo Front Clear Brake Reservoir Tubing
*Brembo CNC 108mm GP4-RR 32/36 Monoblock Front Calipers with Nickel Cadmium Finish
*Brembo HP Rear Caliper
*Ferodo SinterGrip XRAC Racing Brake Pads (with Array Cooling)
*Brembo (Model: x98.A7.C1) GP Billet LTD Race Radial Pump 19x18 Rossi/Hayden Front Brake Master Cylinder
*Galfer Rear Custom Superbike Brake Line
*HRC Rear Brake Reservoir Kit
*Spiegler Custom 3 Line Type 950 Fitting Brake Lines
*Spiegler Dry Brake Sockets with Banjo Fittings
*Spiegler Quick Disconnect Dry Brake Plugs

-Controls-
*Attack Performance Upper & Lower Triple Tree Clamps with Custom Ignition Bracket
*Brembo Clutch Half Lever
*Brembo HPK Clutch Cable Perch
*Brembo GP Master Cylinder Half Lever
*Brembo GP Remote Adjuster with Graves Motorsports Bracket
*Renthal Adjustable Clipons
*Sato Racing Adjustable Rearsets with GP Shift

-Body & Paint-
*3M Paint Protective Film by Elite Auto Films
*Catalyst Composites Race Bodywork
*CleverWolf Racing Carbon Rear Hugger
*Custom Painted “50th Anniversary of Grand Prix Racing in Red & White” by MotoGloss
*Decals by Ace Custom Graphics & Fatlace
*Graves Gloss Black Fairing Stay
*GTYR Carbon Exhaust Heat Shield
*Puig Clear Double Bubble Windscreen

-Accessories-
*Accosato Quick Release Gas Cap
*Driven Preload Gold Fork Adjustors
*Driven Hand Grips
*Gilles Chain Adjusters
*Gilles GP Lifts
*Graves Left Engine Crankcase Cover
*Graves Quick Release Fairing Stay Race Fit
*Graves Rear Brake Return Spring
*H20 Performance Custom Oversized Radiator Guard
*HRC Overflow Radiator Bottle with Brembo Clear Reservoir Tubing
*Intuitive Frame Sliders
*Moose .028 Safety Wires
*ProBolt Titanium Sump Oil Drain Plug Bolt
*ProBolt Titanium Rear Axle Nut
*ProBolt Titanium Swingarm Adjusters
*ProBolt Titanium Unsprung Race Bolt Kit with Predrilled Heads
*Racebolts Titanium Front & Rear Axles
*Racebolts ¼ Turn D-Ring Fasteners
*R&G Clutch and Shifter Sliders
*R&G Swingarm Sliders
*RhinoMoto Fork Sliders
*RhinoMoto Rear Axle Sliders
*Rizoma Oil Cap
*Rizoma Pro Guard System Hand/Lever Protectors
*StompGrip Clear Four Piece Tank Kit
*StompGrip Clear Tank Protector
*StompGrip Clear UniTankTop
*Woodcraft Left & Right Engine Case Covers
*Valter Moto AR50 Aluminum Pro Racing Rear Prong Paddock Stand
*Yoyodyne Rear Titanium Race Caliper Bolts with Predrilled Heads
GGGGGGGGGGGGGRRRRRRRRRRRRREEEEEEEEEEEEEEAAAAAAAAAAAAAATTTTTTT
BIKE...That's all folks...
 
#116 ·
Ur one sick mother**** :lol
 
#117 ·
Dude! I saw your bike at Laguna's motogp round in 2010. I took enough pictures to do what I would consider somewhat copy your design. A week later I started my own project. Unfortunately, the person I had do the paint all but jacked it up. (Thanks Paint by Camille!) But, what I will say is that your bike looks even better now! So you're on another level with everything you've done overall.
 
#118 ·
Hey guys, I actually took 2nd place at the Long Beach Convention Center last weekend. There was controversy with that cuz most builders were shocked that I didn't take 1st. The bike that took 1st was a stretched out RC51. I'd understand if it was better than mine but in honesty it wasn't great at all. All I know for sure is that it didn't have a long list of upgrades as I did...
Please give your feedback on this web link: https://www.facebook.com/photo.php?...3397446.-2207520000.1355634320&type=3&theater
 
#123 ·
I've seen you post this bike before but not sure how I missed this thread.

Congratulations!!! Well deserved.

1 question.. why the BMW coolant?
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top