Yamaha R1 Forum: YZF-R1 Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-15 of 16 Results
  1. 98-99 Performance Group
    My clutch slipped at 200 km / h, after replacing it with an EBC plate, the problem disappeared, but the clutch cable broke 2 times already, it is 30% harder to squeeze the clutch
  2. 07-08 R1 Mechanical Help
    I HAD RECENTLY PURCHASED THIS BIKE AND TO MY KNOWLEDGE ALL IT NEEDED WAS A CLUTCH CHANGE SO I WENT AHEAD AND CHANGED THE CLUTCH AND IT WENT INTO GEAR FINE BEFORE THE CHANGE. NOW IT WONT GO INTO GEAR ITS STUCK IN FIRST WHICH IS THE GEAR I LEFT IT IN FOR THEW CLUTCH CHANGE BECAUSE I FORGOT TO PUT...
  3. 04-06 R1 Mechanical Help
    Bit of an intro too, so please skip to the last two paragraphs for the questions... Hi all, So I've ridden various, mainly small ish bikes, for years. Love tinkering with engines. I've ridden 50's to 1000's, but never owned a 1000cc of my own before. I did swap bikes for a while (my 2002...
  4. 04-06 R1 Mechanical Help
    So I was cruising when my bike over heated. I was going around 80 mph when I saw my temp light on. Both fans were running and the temp gauge was reading 250 degrees F. I was gonna pull over on the side of the highway but couldn’t cause traffic. Seconds later, as I was pulling over coolant...
  5. 07-08 R1 Mechanical Help
    Hello, First of all, sorry for the broken english and secondly thank you for helping. So I bought a 2008 (4c8) Yamaha R1 and it propably had wrong motoroil as the clutch had burned here and there (the metal plates). Also when starting off, the bike "rumbles" forward and will stall if I don't...
  6. General Motorcycle Discussions
    hey guys anyone here done a clutch replacement on a 15-19? I ordered a Barnetts rebuild kit but when I opened up the cover and pulled the pressure plate and old frictions/steels I found this… obviously I know this is bad but should I go ahead and replace the basket and pressure plate as well...
  7. General Motorcycle Discussions
    Just thought I would ask a quick question regarding the clutch basket on the 04 r1. Now I know the dampening springs in the back can get excessively loose and cause a rattle on idle, and in my case when I pull the clutch lever the rattle stops. I’m just trying to work out if when I’m engaging...
  8. 09-14 R1 Mechanical Help
    I have a 2013 r1 with 14k miles, I've put about 3k miles on it since ive owned it. There are a couple things that are concerning me about the bike but have not ridden another r1 to compare it to so maybe its normal? First off when I'm in neutral, there is a noticable vibration and sound...
  9. 07-08 R1 Mechanical Help
    Hey guys, first time poster. Usually I manage to browse straight off Google but this one has done my head in. I replaced the clutch discs on my 08 R1 (have done this job before on another bike) but since completing the job it won't fully disengage. Cable has been adjusted fully, bike was...
  10. 98-99 R1 Mechanical Help
    Hey guys, new to the forums and after a little help, I’ve tried anything I can find about my issue to no avail… I have a 1999 Yamaha r1 and on a track day a few weeks ago on my final laps my clutch started slipping and making a right noise, long story short I took apart the clutch and some of...
  11. 09-14 R1 Mechanical Help
    Hello, So I was upgrading my clutch and decided to replace the entire clutch(springs,plates,fiber plates). I followed the manual and everything was fine till I snapped one of the screws on the pressure plate. So I decided t take everything apart so I can get that screw out which I did. After a...
  12. Appearance & Mods
    Hello, has anyone of you mounted this model of levers? Do you know if they are compatible with the 2004-5-6 model?
  13. 98-99 R1 Mechanical Help
    Hello fellow R1 enthusiasts. I'm new here. Im also hoping someone can help me find some parts. Is there anywhere that I can buy a shock rebuild kit aftermarket for a 98? Im also having trouble finding a clutch. Im also wondering about getting the ECU flashed. The exhaust valve was stuck very bad...
  14. General Motorcycle Discussions
    Hi team, I purchased my own Yamaha r1 2007 finally, after years of thoughts and dreams. And although it’s the second day, i am feeling a bit negative about my whole experience. The bike looks and perform great, but my big problem is that i found it extremely difficult to drive this bike for...
  15. Bikes/Parts Wanted
    Looking for the nut that hold the inner clutch hub onto the input shaft. Checked all the major online suppliers and no one has one in stock. Picture attached showing the exact nut I'm looking for.
1-15 of 16 Results
Top