Yamaha R1 Forum: YZF-R1 Forums banner
Cancel

Posts by ImagineParadise

Jump to Latest Follow
1 - 20 of 21 Posts
I

· Banned
Joined
·
3,451 Posts
#13 · (Edited)
ugh, noobs, watch this...

Go into your Network settings..
Thats
Start, Settings, Network.
Then Right click your network.
Be sure to have the following installed AND checked...
~CLIENTS~
-Client for MSN
~SERVEICE~
-File and Printer Sharing For MSN
~PROTOCALLS (you might need your windows disk) to install
-NWLink Net BIOS
-NWLink IPX/SPX Net BIOS Compadible Transport PRotocall
-Internet Protocal (TCP/IP)

If you have all these installed and checked then what you need to so is uninstall and reinstall them again. THEN restart all your comupters. This should work. If not, I have a lot more suggestions but first try that.

BE SURE TO DO THIS ON ALL COMUTERS


AD make sure you right clicked the hard drives of all the computers and under "Sharing and security" make sure on ALL computers that you have the right boxes checked. (on my network I have all my computers HD sharing with each other with no limitations.)
 
I

· Banned
Joined
·
3,451 Posts
#23 ·
plus, be sure under your network settings...thats,

Start-Settings-Network Connections,
~right click your network, then highlight your TCP/IP and hit properties.
Then check to see if you have your IP and DNS obtained automaticly. Then, hit advanced. Make sure that ONLY the DHCP is enabled and click on over to the DNS tab.

Make sure that your Primary and Parent suffixes are checked. And check the registerd for DNS close to the bottem. Then under the WINS tab, be sure to have the "Enable LMHOSTS lookup" is clicked, along with the "default" net bios settings.
One more thing is to check your router IP page to make sure you have it set up correctly.
Hope this helps!
 
I

· Banned
Joined
·
3,451 Posts
#35 ·
AHHAHAHAHAHh, man, I need to read things through slowly, peice by peice. I didnt even catch this....

Hell Shadow, if you need a copy of XP pro just let me know, you've found out the hard way (sorry I didnt catch that earilier) that ME is the worst operationg system by far for ANYTHING.
I would quit while your ahead. The more you mess with ME the worse it gets.
 

Attachments

I

· Banned
Joined
·
3,451 Posts
#37 ·
another suggestion is to see whether or not your computers can ping each other and other websites.
if you can go into your dos prompt, or go to "run" and type "cmd" (try this on both computers) when your in dos, type "ping *your other computers IP address*" and see whether it times out or if it pings your other computer. For example, i would type "ping xx.xxx.xx.xxx" and I'd see what it does. Also, try to ping other websites, such as "ping www.yahoo.com" or something along those lines. Tell me what happens.
 
I

· Banned
Joined
·
3,451 Posts
#53 ·
Shadow R One said:
Ok... good news and bad news.
I swapped out network cards and the network works.. kinda.
I can access her computer now... but not the internet...
Maybe I have something messed up with the TCP/IP portion :(
Click to expand...
Did you reset the Modem and the router's memory by doing my steps of turing off everything (unplug Modem nad router)? If you follow my steps Im sure it would work (praying) Here, after unplug/turned off do this
wait 30 sec
turn on modem
wait 30 sec
turn on router
wait 30 sec
turn on computers. Hope you get it!
 
I

· Banned
Joined
·
3,451 Posts
#55 ·
I'm telling you, you need those protocals w/ win '98 and win ME. Hell, Im on XP and I STILL have to have those protocalls installed. Remember when I was building this computer and I posted some stupid thread doing this...
Computer 1 ....
next messege
Computer 2 ....
next messege
Computer 1 ....
next messege
Computer 2 ....
next messege

I was doing that while the protocals were installed. I could NOT connect to the internet on this one without the protocals
here, Ill try and find that networking website that helped me out...
 
I

· Banned
Joined
·
3,451 Posts
#59 ·
Shadow R One said:
Hmmm... the one that I dont have is the NW Net BOIS one... I guess I got the other one confused with it... Funny thing though is that it is not listed in the available protocals :confused: and I dont know where on the windows cd it is in
Click to expand...
Thats on my XP machine I just built, Let me have a screen shot of the protocalls you have on the ME machine.
 
I

· Banned
Joined
·
3,451 Posts
#62 · (Edited)
Ok, lets say your right val. Your way is pretty simple. Dry and cut instructions. But, if your right, why hasnent it worked for him? We've tryed about everything and it still hasent worked. You know what I think, and I've said it before, is that I should send him a copy of winxppro and kill that fcked up ME he has. Then we'll try your way again. Simple, clean cut. Very easy way. If that doesnt work then we try it my way. As soon as he can get XPpro on his PC, we'll start up the instructions again. And you can go first. I still dont get it though. I had the same setup with my roomie last year and he had....o shit..we only had a switch....Shadow, your not using the switch in the circuit are you? It should go Cablemodem to router then from the 4 port or 8 port router should be your computers with no switch in between. It may sound obvious but Im just trying to go over everything that I can think of.
O and make sure your NOT useing crossover cable inbetween any connection and only CAT5 or CAT6 ethernet cable.
 
1 - 20 of 21 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
About this Discussion
72 Replies
13 Participants
Last post:
CCIE2BE
Yamaha R1 Forum: YZF-R1 Forums
R1-Forum is a Yamaha R1 motorcycle enthusiasts community dedicated to Yamaha YZF 1000 R1 sportbike. Discuss performance, customization, specs, reviews and more!
Full Forum Listing
Explore Our Forums
General Motorcycle Discussions Appearance & Mods Bikes For Sale Bike Parts For Sale Bikes/Parts Wanted
Top